Interesting and Instructive ArticlesWaggoner eNews

Dripless Shaft Seals

Advocates of dripless shaft seals are quick to point out their benefits over conventional stuffing boxes – no leaks, no flax to replace, no shaft scoring. But, the zinger is always the same. While it’s true dripless shaft seals require less care than a traditional packing gland, nothing on a boat is truly maintenance free.

Dripless shaft seals have become widespread in the past decade and a half, but when a dripless shaft seal fails, the resulting flooding is alarming at the very least, and potentially catastrophic. The goal here is to review the ways dripless shafts fail and offer some preventive maintenance suggestions.

Disclosure: There are affiliate links in this post. 

Dripless Shaft SealsDripless Shaft Seals – How They Work

There are a number of manufacturers of dripless shaft seals and a variety of designs. Most of the units use what’s called a face-type seal, with flexible bellows attached to the stern tube (or stuffing box collar) that presses a fixed carbon/graphite flange against a rotating stainless-steel rotor which spins with the prop shaft, creating a seal between the rotor and flange. The compression created by the flexible bellows hose plays a key role in the stuffing box’s proper, leak-free operation.

Dripless Shaft Seals

Dripless Shaft Seals – What to Look For

Dripless seals are popular because they don’t require adjustment after installation and they continue to keep sea water out even if the drive train is out of alignment, producing a dry bilge and creating a safer, cleaner, more corrosion-resistant and sweeter smelling vessel.

Some dripless shaft seal products use set screws to hold the rotor in place. If the screws lose their grip, the bellows can slowly push the rotor forward on the prop shaft. Once the bellows are relaxed, the mechanical seal between the rotor and flange is lost, and sea water can flow into the bilge. It happens more often than you might think. According to one manufacturer’s instructions, the setscrews are never to be reused, and a new set of screws should be used each time the rotor is installed.

Another issue with a spinning rotor is that the flange and rotor are so well mated that there is a suction effect between them, and the rotor can actually stretch the bellows beyond its relaxed position before the seal is broken. So, when the bellows finally returns to its natural, relaxed position, a tiny space is left between the flange and rotor.

The key to preventing setscrew and rotor movement problems is to place a hose clamp on the prop shaft up against the forward face of the rotor, so that even if the rotor works loose, the hose clamp will prevent the rotor from moving away from the flange.

The Bellows

The bellows perform two functions. First, it creates a watertight barrier between the stern tube and the interior of the boat. Second, it acts as a spring, pushing the flange against the rotor. Problems associated with the bellows are related to fatigue, mechanical abuse, or improper installation.

Bellows fatigue can occur as the bellows material deteriorates over time. Exposure to heat, vibration, saltwater and accidental spills of fuel and fluids can take their toll. The material can become brittle with age, and a close inspection might reveal cracks, splits, or tears – problems may not be readily apparent on the surface of the bellows. For a proper inspection, at the very least, the rotor should be moved a few inches out of the way so that it can relax and so that stretching and twisting can reveal any cracks or splitting of the material. As a general rule, if the shaft is removed, new bellows should be installed.

The second form of fatigue consists of what is known as “compression fatigue,” where the bellows lose its resistance to compression after years of being in a compressed state. As a result of compression fatigue, the pressure between the rotor and flange will be reduced, which diminish the mechanical seal.  Eventually, it will begin to leak.

Dripless Shaft Seal Kit

Dripless Seal Shaft Kit

Dripless Shaft Seals – Preventive Maintenance

Too many boaters have a “set it and forget it” attitude about their shaft seals and they don’t realize the consequences of ignoring an aging or damaged unit on their vessel. While a dripless shaft seal may be “dripless,” it is definitely not maintenance free.

As with any rubber hose below the waterline, it must be inspected regularly for signs of cracks, wear, aging, or chemical deterioration. PYI recommends inspecting the bellows for cracks, splits tears, and brittleness twice annually and replacing every six years regardless of condition, at which time they also recommend the O-rings and set screws in the stainless steel rotor be replaced as well. This is advice that every boat owner with dripless shaft seals should heed.

Most dripless shaft seal units have a small barb fitting on the graphite flange where a hose can be connected to ensure that water is always present right up to the rotor. From the fitting, the hose runs either to a place high above the waterline or, in the case of higher speed vessels into the engine’s raw-water cooling system.

The cooling water intake hose should be pulled semiannually and checked to ensure seawater is flowing unimpeded. With the engine running and in neutral, remove the water feed line, cap the seal fitting, and capture the flow in a bucket. Flow should be about one gallon per minute at engine idle. Increase your throttle to ensure flow at all engine speeds.  Dress the hose and secure.

A new or well-maintained dripless shaft seal will do exactly what the manufacturer claims it will do: provide a vibration tolerant, drip free stuffing box. Be sure to follow the manufacturer’s maintenance instructions and incorporate them into your routine maintenance schedule.

 

~Deane Hislop


WestMarine.com

Share this: